Steam Learns to Move

Railways: How the Iron Road Changed the World

Course 41 · Chapter 2 · Steam Learns to Move

Railways: How the Iron Road Changed the World 1 ended with a missing piece: good rails, but nothing better than the horse to pull along them. This chapter follows the engine. It starts with the big, slow engines that pumped water out of mines, moves through the leap to high-pressure steam, and arrives at the first locomotives that ran on rails. It ends with a plain-language tour of how a steam locomotive actually works. As before, dates and "firsts" are flagged "check".

Newcomen: Steam as a Pump

Mines went deeper, and deep mines flood. Thomas Newcomen, an ironmonger from Dartmouth in Devon, built an engine to pump water out, with the first well-known installation near Dudley in 1712 (check). It was an "atmospheric" engine: steam filled a cylinder, then cold water sprayed in made it condense, leaving a partial vacuum, and the weight of the atmosphere pushed the piston down. The piston was linked to a huge rocking beam that drove the pump.

The design worked, but it was wasteful. Heating and cooling the same cylinder every stroke burned a great deal of coal, which hardly mattered at a coal mine and mattered a great deal anywhere else. It was also enormous and fixed in place, so it could never be put on wheels.

Watt: A Separate Condenser

James Watt, repairing a model Newcomen engine in Glasgow in the 1760s, saw the waste: the cylinder was being reheated after every cooling. His fix, patented in 1769 (check), was a separate condenser, so the cylinder could stay hot while condensing happened elsewhere. Working with the manufacturer Matthew Boulton in Birmingham, Watt went on to add features such as a double-acting piston and rotary motion, so engines could drive mill machinery as well as pumps. Watt's engines used steam at low pressure, little above the atmosphere, and he was cautious about higher pressures, partly for safety and partly because his patents protected the low-pressure design (check the exact reasons).

Engine (check each)How steam is usedLimit for a locomotive
Newcomen atmosphericSteam condensed in the cylinder; air pressure pushes the pistonVery heavy for the power, and wasteful of fuel
Watt low-pressureSeparate condenser; steam pushes as well as airCondenser and beam make it bulky; low pressure means low power for the weight
High-pressure (Trevithick)Steam well above atmospheric pressure drives the piston directlyNeeds a strong boiler, but small and light enough to move

High Pressure Makes It Small

A locomotive must carry its own engine, so the engine must be small and light for the power it gives. The way to get more power from a smaller cylinder is higher steam pressure, and the exhaust steam can simply be released into the air, with no condenser to carry. This was the route taken by the Cornish engineer Richard Trevithick, who built high-pressure engines in the late 1790s and early 1800s, and by the American Oliver Evans, who worked on similar ideas at about the same time (check the relative priority). The price was safety: a boiler under high pressure that fails can explode, and early boilers did fail, which is one reason the topic raised fear in the public as well as hope.

The idea in one line The locomotive became possible when engineers stopped trying to improve the huge fixed pumping engine and instead made the engine smaller and stronger by using high-pressure steam and letting it escape up a chimney.

Trevithick's Locomotives

Trevithick put a high-pressure engine on wheels in the first years of the nineteenth century. A road carriage, the "Puffing Devil", is usually dated to 1801 (check). The better-documented railway milestone is the Penydarren locomotive of 1804, built for the Penydarren ironworks tramroad in South Wales. It is commonly described as running on 21 February 1804, hauling about ten tons of iron and a number of men, though one source gives a slightly different day (check the date, the load and the exact distance). It worked, but its weight cracked the brittle cast-iron plate rails, and the experiment did not continue at Penydarren. Trevithick also made a locomotive in 1808, "Catch Me Who Can", which ran as a London attraction on a circular track (check).

One detail in the 1804 engine mattered later: waste steam was turned up the chimney. The blast of exhaust steam drew air through the fire and made it burn hotter, so the boiler produced more steam when the engine worked hardest. This steam-blast principle stayed a feature of steam locomotives for the next century and a half.

Blenkinsop, Murray and the Rack Problem

An early worry was grip. Would a smooth iron wheel on a smooth iron rail simply spin? John Blenkinsop, a mine manager at Middleton near Leeds (the same railway you met in Railways: How the Iron Road Changed the World 1), patented a different answer: a toothed rail along one side, driven by a cog on the locomotive. The engineer Matthew Murray built the engines, and the first ran in 1812, with "Salamanca" among the best known (check the dates, which vary between 1811 and 1812 in sources). They are often called the first commercially successful locomotives, because they worked daily hauling coal for years. The next step showed that the grip worry was overstated: adhesion, plain friction between wheel and rail, was enough for heavy loads on gentle gradients, as William Hedley's "Puffing Billy" at Wylam colliery in the 1810s helped to show (check).

Early locomotive (check each)DateNotable feature
Penydarren (Trevithick)1804High-pressure steam, chimney blast; broke the plate rails
Salamanca (Murray, for Blenkinsop)1812Rack drive, twin cylinders, in daily commercial service
Puffing Billy (Hedley and others)c. 1813-14Adhesion drive; long working life on colliery lines
Locomotion No. 1 (Stephenson)1825Opens the Stockton and Darlington line, the subject of Chapter 3

How a Steam Locomotive Works

Strip away the detail and a steam locomotive is a mobile kettle connected to a pair of pistons. The pieces work in a loop:

PartWhat it does
FireboxBurns coal (or wood or oil) on a grate. The hot gases are the energy source.
BoilerA pressurised tank of water. Hot gases pass through tubes running through the water, heating it into steam. More tubes means more heating surface and more steam.
Regulator (throttle)A valve the driver opens to let steam flow from the boiler towards the cylinders.
Cylinders and pistonsSteam pushes the piston one way, then the other (double-acting).
Valve gearSlide or piston valves that direct steam to the correct side of the piston at the right moment, and which can be adjusted to run the engine forward or in reverse and to use less steam at speed.
Connecting rods and wheelsThe to-and-fro piston motion is turned into wheel rotation, like pedals turning a bicycle crank.
Blastpipe and chimneyExhaust steam is sent up the chimney, drawing the fire.
TenderA truck behind carrying the coal and the water that the engine consumes.

The cycle is easy to follow as a list of steps, shown below in a pseudo-code form. It is a teaching model, not a real controller.

# A teaching model of one working cycle of a steam locomotive while locomotive_is_running: fire.burn(coal) # 1. firebox makes hot gas steam = boiler.heat(water, fire.gas) # 2. boiler turns water to steam if regulator.is_open: cylinder.push_piston(steam) # 3. steam pushes the piston wheels.turn(piston.motion) # 4. rods turn the wheels exhaust = cylinder.release() # 5. used steam leaves chimney.draw(exhaust) # 6. exhaust draws the fire harder tender.supply(coal, water) # 7. crew shovel and refill
Did you know A steam locomotive is a very inefficient machine by modern standards: only a few percent of the energy in the coal ends up at the wheels (check the figure, which varies with the engine). It dominated for over a century because it was powerful and robust and made from simple parts, not because it was efficient.
Modern parallel The step from Watt to Trevithick is like the step from the mainframe to the laptop: the same basic idea, but miniaturised and pushed to higher performance per kilogram until it could be carried around. A fixed machine that served one site became a mobile one that could be sent anywhere there was a track.
Watch out "Stephenson invented the locomotive" is a very common claim and it is wrong. Trevithick, Murray and Blenkinsop, and Hedley had all run working locomotives before George Stephenson built his first in 1814. Stephenson's achievement, in the next chapter, was to turn the locomotive into the engine of a reliable public railway.
Verified / Not Yet Verified Verified by a web search for this chapter: Trevithick built the Penydarren locomotive in 1804 (most sources give 21 February, one a few days earlier); its exhaust steam was sent up the chimney; and Matthew Murray built the Salamanca engine for Blenkinsop's rack system at the Middleton Railway in 1812 (sources vary on the exact month of the first engine, with June and August both appearing). Not verified: the search returned nothing on Newcomen's 1712 engine or Watt's 1769 patent, the Puffing Devil date, Oliver Evans, Hedley's Puffing Billy dates, or the efficiency figure. Those come from general knowledge, so treat every "(check)" accordingly.

Exercises

Exercise 1

Explain in your own words why Watt's improvement, good as it was, did not lead straight to the locomotive, and what Trevithick changed to make a mobile engine possible.

Exercise 2

Trace the path of the energy in a steam locomotive, from the coal on the shovel to the turning wheels, naming each component it passes through. Then say where most of it is lost.

Exercise 3

A friend says "George Stephenson invented the railway locomotive". Write a short, fair reply that credits earlier engineers, names at least three of them with what each contributed, and states what Stephenson's real contribution was likely to be (to be tested in Chapter 3).

Coming up Chapter 3 meets George and Robert Stephenson: the Stockton and Darlington Railway, the Rainhill Trials and the Rocket, and the Liverpool and Manchester Railway, the first main line with steam traction and a timetable for both passengers and freight.

Quick Reference

  • Newcomen (1712): atmospheric pumping engine, huge and wasteful
  • Watt (1769 patent): separate condenser, much better fuel economy, still low pressure
  • Trevithick (1804): high-pressure steam, exhaust up the chimney, first rail locomotive run in Wales
  • Blenkinsop and Murray (1812): rack locomotives in daily colliery service at Middleton
  • Locomotive in brief: firebox, boiler, regulator, cylinders, valve gear, rods, wheels, blastpipe, tender