Engineering the Route
Railways: How the Iron Road Changed the World
Course 41 · Chapter 7 · Engineering the Route
Railways: How the Iron Road Changed the World 6 showed railways imposing a common time. This chapter looks at the physical side: how a line was laid across real land. A railway wants a route that is nearly level and nearly straight, and the land is neither, so engineers cut, filled, tunnelled and bridged. As before, dates, lengths and "firsts" are flagged "check".
Why Railways Want Flat Ground
A steel wheel on a steel rail has very little friction. That is the great strength of the railway, since a small engine can pull a heavy load, and also its weakness, because the same low friction means a train struggles to climb and can slide when braking or starting on a slope. A road for horses could follow the shape of the land, but a railway engineer tried to keep gradients gentle (a gradient is how much the line rises over a distance; check typical limits for early main lines, which were often quoted as only a small fraction of a percent to a couple of percent). Curves matter too: a tight curve slows trains and wears wheels and rails. The route, then, is a trade-off between the cost of changing the land and the cost of running trains over a poor line for ever.
Surveying: Choosing the Line
Before any digging, surveyors walked the land with levels and measuring chains to map heights and distances and to pick a line. Because a railway usually needed an Act of Parliament in Britain (see Railways: How the Iron Road Changed the World 4), the survey also had to produce plans and sections to be deposited and argued over, and some landowners tried to turn surveyors away from their land (check some examples). A poor survey cost money twice: once in the construction and again in the running of the line, which is why the best engineers were paid well for it.
Cuttings and Embankments
The simplest way to keep a line level is to balance cut and fill. Where the ground rises, the builders dig a cutting, and where it falls, they pile up an embankment. Ideally the earth dug from the cuttings is carted along the line to build the embankments, so little has to be brought in or taken away. Nearly all of this work was done by hand with picks, shovels, barrows and horses, with gunpowder for rock, by the navvies described in Railways: How the Iron Road Changed the World 4. Cuttings brought their own dangers, including landslips in clay and the long job of draining water away from the track (check some famous slips). Embankments could sink or slide if not built carefully, and some took far more earth than the engineers had estimated.
| Feature | What it does | Main problem |
|---|---|---|
| Cutting | Digs down through a rise to keep the line level | Slips, water, spoil to dispose of |
| Embankment | Builds up across low ground | Settling, slipping, huge volumes of earth |
| Tunnel | Goes through a hill or under a feature | Cost, ventilation, flooding, collapse risk |
| Viaduct | Carries the line over a valley on arches or piers | Cost of materials, foundations |
| Bridge | Crosses a river, road or estuary | Span length, strength, foundations in water |
Tunnels
When a hill was too high to cut through, the line went through it. Tunnelling by hand was slow and dangerous. Builders usually sank vertical shafts along the route, dug outwards from the bottom of each shaft, lined the bore with brick and met in the middle (check how closely the headings met on famous tunnels). Gunpowder was used for rock, and water and falling ground were constant threats. Many men were killed or injured on the big tunnels (check the figures for particular tunnels).
Two British examples show the scale. The Great Western's Box Tunnel near Bath, opened in 1841, is about 1.8 miles long (check the exact length and date; sources give 30 June 1841), and was considered a bold undertaking because of its length and the rock it passed through. The Woodhead Tunnels carried a line across the Pennines, the first opening in 1845 and being roughly three miles long, among the longest of their day (check the length; sources differ by a few yards). Woodhead's story also shows how a route could change hands, with Charles Vignoles starting the design and Joseph Locke later taking over (check the details of this change).
Viaducts and Great Bridges
Valleys were crossed by viaducts, long bridges of many arches or piers, built in brick, stone and later iron. They were costly, but they let the line stay level and so were often cheaper than losing a gradient over the whole life of the railway. Bridges across rivers and estuaries needed a different skill, because the span might be wide and the foundations had to be built in water, often using caissons, which are watertight boxes or cylinders sunk into the bed so workers can build in the dry (check how particular bridges were founded). Famous examples include Brunel's Royal Albert Bridge over the Tamar at Saltash and Robert Stephenson's Britannia Bridge over the Menai Strait, which used huge wrought-iron tubes through which trains ran (check the dates and design of each). For the principles of how a bridge carries its load, see How Bridges Work.
The Track Itself
On top of the earthwork sat the track. Rails rested on sleepers (the cross-pieces, mostly timber), which in turn rested on a bed of broken stone called ballast, whose job is to hold the sleepers in place and let rainwater drain away. Early rails were short and made of cast or wrought iron, and later rails were made of steel, which lasted far longer (check when steel rails became common). Rail shapes and the way rails were fixed varied between companies and countries, and this is the sort of detail that later became standardised, as the earlier chapter on gauges suggested (see Railways: How the Iron Road Changed the World 5).
Signals: A Glimpse
Because trains cannot swerve, the safe way to run a busy line was to keep trains apart. The earliest methods relied on timetables and on men waving flags or lamps, and signal posts with moving arms (semaphore signals) developed later. The full story of block signalling, interlocking and the lessons from accidents belongs to Railways: How the Iron Road Changed the World 9, so this chapter notes only that the route and its signals were designed together.
Exercises
Explain why railway engineers wanted a nearly level, nearly straight route, and what a cutting and an embankment each do to help.
Compare a tunnel, a viaduct and a bridge over an estuary: what problem does each solve and what is the main difficulty of building it?
Describe the layers of a simple track bed (rail, sleeper, ballast) and explain, using a modern parallel, why paying more for a good route up front can save money later.
Quick Reference
- Why level: steel on steel has low friction, so slopes and tight curves hurt trains
- Cutting / embankment: dig down through rises, build up across hollows; balance the earth
- Tunnel: through a hill, via shafts and brick lining (Box 1841, Woodhead 1845)
- Viaduct / bridge: carry the line across valleys, rivers and estuaries
- Track: rail, sleeper, ballast